Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Why Lakewood Homeowners Choose Trane Air Duct Cleaning
We provide independent Trane air duct cleaning and air-handler service in Lakewood, and what sets our Trane work apart is that we know the hardware from the inside: the Hyperion cabinet with its all-aluminum coil, the variable-speed XV air handler, the S9V2 furnace and its matching cased coil. We clean the coil, the blower and the trunk, then fix what’s leaking. We’re not affiliated with or authorized by Trane, and we don’t pretend to be. Our technicians have up to 9 years of experience with these systems, and we work on the Trane equipment we find across Lakewood every week.
Key Takeaways
- We service and clean Trane Hyperion, XV variable-speed and S9V2 systems as an independent provider, not an authorized Trane dealer.
- Our focus is Trane’s evaporator coil, blower wheel and cabinet seams, not just the visible duct runs.
- We use Rotobrush and Nikro professional-grade systems and Abatement Technologies equipment, not shop vacs.
- We clean ductwork and repair it on the same visit, so a leaking cabinet doesn’t undo a good cleaning.
- Call (844) 914-0778 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Lakewood Duct Cleaning for Your Trane Air Duct Cleaning?
Trane air handlers have their own patterns. A Hyperion cabinet is built around an all-aluminum coil, and that coil behaves differently under a dust load than older copper-and-fin assemblies. Variable-speed XV systems run long, low-speed cycles. The S9V2 furnace sits in a cabinet with factory gaskets that are good but not perfect after years of cycling. We know these quirks because we see them, not because any manufacturer told us about them.
When we clean a Trane system, we treat the air handler as the center of the job, because it usually is. Dust that leaves the coil ends up in the supply trunk. Dust that bypasses the filter at the coil door ends up on the coil. Cleaning one without the other just moves the problem around. Our technicians have up to 9 years of experience working with Trane equipment, and they clean and repair to keep the system’s airflow and your warranty intact.
Parts matter here. Commodity items (filters, foil-backed flex, mastic, gasketing) we source from quality manufacturers rather than paying an OEM premium. Trane-specific coil, blower and control parts are genuine OEM, because fit and airflow calibration on a Trane cabinet aren’t something to improvise. If a coil is leaking refrigerant or a cabinet has rusted through, cleaning won’t fix that, and we’ll tell you so.
Styles & brands we work with
- Whole-home duct cleaning
- Dryer vent cleaning
- Camera inspection
- Sanitizing & deodorizing
Common Trane Air Duct Cleaning Problems We Fix in Lakewood
Most Trane duct problems in Lakewood are not duct problems at first. They start at the air handler or the cabinet seal and show up downstream. Here are the ones we find most often in Lakewood homes.
- The Hyperion all-aluminum coil collects a matted dust load. When a loaded media filter restricts airflow, the aluminum coil fins wet and trap fine gray dust. That layer eventually sheds downstream into the supply trunk. Homeowners notice the dust on their registers and weak airflow to far rooms before they ever look at the coil.
- The XV variable-speed air handler plates its blower wheel. Long, low-CFM runtimes on XV systems let light dust stay airborne longer, so it settles on the blower wheel and ECM motor housing instead of in the filter. The wheel goes unbalanced and airflow drops. You hear it before you see it.
- Cabinets leak at the coil door and drain pan lip. Trane builds factory gasketed seams and knockouts into these cabinets, but seals age. Unfiltered attic or garage air gets pulled into the return and dusts the supply side. In Lakewood’s older ranch homes, that’s often crawlspace or attic air coming in.
- The S9V2 furnace and XC95m trap lint near the secondary heat exchanger. Lint and pet hair collect in the draft inducer area and around the secondary exchanger. The symptom is often musty odor and reduced airflow, not a visible duct problem. It’s easy to miss on a standard cleaning.
- Original rigid duct runs have never been cleaned. Much of Lakewood’s housing dates to the 1950s through the 1980s, and in the older neighborhoods west of Wadsworth it’s common to find 1960s furnaces and unsealed duct trunks pulling attic and crawlspace air. Decades of high-desert grit caked onto the walls of galvanized duct won’t lift with a shop vac.
Trane Parts & Our Repair-vs-Replace Approach
We don’t stock OEM Trane parts and we’re not a Trane dealer. What we do is choose the right part for the job. Filters, foil-backed flex, mastic and gasketing come from quality manufacturers because a $40 filter is a $40 filter. Trane-specific coil, blower and control parts are genuine OEM because fit and airflow calibration matter on a Trane cabinet, and a wrong blower wheel will cost you more in airflow performance than it saves.
The repair-or-replace call is usually obvious once we’ve opened the cabinet. A coil with a dust load gets cleaned. A coil with a refrigerant leak gets replaced as a component. A rusted-through cabinet gets replaced. Cleaning alone won’t fix a failed part, and we won’t pretend it will. Once we’ve inspected your Trane system in Lakewood, we give you a written estimate before any work starts. Call (844) 914-0778 for a free estimate.
Our Trane Service Process – Step by Step
- 1
Diagnose. We open the air handler, check the coil, blower wheel, cabinet seams and drain pan, and take static pressure readings before we clean anything. On a Trane Hyperion or XV system, that means going in expecting to find dust on the coil or the blower, not just in the ducts.
- 2
Clean and repair. We use Rotobrush rotary-brush cleaning to dislodge debris from duct walls and Nikro HEPA filtration to capture it at the source. On the air handler, we clean the aluminum coil and drain pan, then seal cabinet seams and knockouts with mastic. If ductwork is compromised, we repair it the same visit.
- 3
Test. We confirm static pressure and airflow after the cleaning. If a far room is still starved, we look for a collapsed flex run or a leaky trunk rather than declaring the job done.
- 4
Warranty and record. We document what we cleaned and repaired. If your Trane warranty is in play, that record shows work was done by an independent shop using quality parts, which keeps the warranty conversation clean.
See the difference
Before
After
Before
After
Before
AfterTrane Products We Service & Install in Lakewood
We service Trane air handlers and the duct systems attached to them. The Hyperion cabinet with its all-aluminum cased coil is one we work on regularly, along with the variable-speed XV air handlers and the S9V2 and XC95m furnaces with matching cased coils. On the outdoor side, XR series air handlers and condensers in XR14 and XR15 paired systems are covered as part of the evaporator coil cleaning side of the work. We don’t install HVAC systems; we clean, seal and repair the duct systems and air handlers those systems depend on, including evaporator coil cleaning, full system cleaning and duct sealing. That’s the scope, and it’s the right scope for what Trane equipment needs on the airflow side.
We Also Service These Brands
We’re not a single-brand shop. Alongside Trane, we work on systems built on Lennox and Carrier equipment when the duct, coil or air handler needs cleaning or repair. The equipment brands matter less than what kind of duct runs you have and whether the air handler is leaking. In Lakewood, we see plenty of both.
FAQs – Trane Air Duct Cleaning Service in Lakewood
No. We are an independent Trane service provider, not authorized by, affiliated with or endorsed by Trane. We service Trane equipment because we work on it regularly, not because we’ve been approved by the manufacturer. That means we can’t sign off on Trane warranty claims, but we can do the duct cleaning, coil cleaning and repair work your Trane system needs and document it. Call (844) 914-0778.
Yes, and mostly because of the coil. A Trane Hyperion air handler with a clogged media filter typically pushes air past the gasketed coil door and loads the aluminum coil fins with a matted gray dust layer, which then sheds into the supply trunk. Homeowners notice dust on registers and weak airflow at far rooms. The usual play is pulling the coil door, cleaning the aluminum coil and drain pan, cleaning the blower wheel, then mastic-sealing the cabinet seams and knockouts and confirming static pressure before and after. A standard cabinet cleaning that skips the coil misses the source.
Because the dust is coming from the blower wheel and the coil, not the ducts. On variable-speed XV systems, the blower wheel and ECM housing are the parts that need the most attention because long low-speed runtimes plate them rather than loading the filter. A duct-only cleaning can leave that dust load intact, and it keeps shedding onto registers. Call (844) 914-0778 for a free estimate that covers the air handler, not just the ductwork.
Sometimes it is, but often it’s the furnace. Lint and pet hair trap in the S9V2 secondary heat exchanger and draft inducer area, and that’s what produces the musty odor and reduced airflow. It shows up as a smell rather than an obvious duct-side symptom, which is why a standard cleaning misses it. We open the cabinet and check before we clean. Call (844) 914-0778 for a free estimate.
Yes, with the right method. Aluminum coil fins bend easily, and a wire brush or high-pressure blast will flatten them and cut airflow. We clean the coil with the gentler approach that Trane’s all-aluminum design calls for, then verify static pressure afterward so we know the coil is releasing air the way it should. Fin damage is a repair cost nobody needs. Call (844) 914-0778 to schedule a coil cleaning.
Usually, yes. Lakewood sits at roughly 5,500 feet with very dry air, intense sun and spring winds that drive fine dust and pollen into return systems. On a 40-to-60-year-old ranch in neighborhoods like Eiber or the Belmar area, unsealed duct trunks pull attic or crawlspace air into the return, and duct sealing is what stops it. It also takes pressure off the air handler. Call (844) 914-0778 for a free estimate and we’ll tell you whether sealing or cleaning is the priority.
Book Your Trane Service in Lakewood, CO
Whether your Trane Hyperion, XV or S9V2 system needs a coil cleaning, a full system cleaning or a duct sealing, we’ll give you a written estimate before any work starts, then clean it and fix what’s broken. Call (844) 914-0778. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’re closed Saturday.
Written by the team at Lakewood Duct Cleaning.